E Series Multifunction DAQ Specifications
275
National Instruments • T
el: (800) 433-3488
•
Fax: (512) 683-9300
•
[email protected] •
ni.com
16-Bit E Series Specifications
Measurements
External Input for Digital or Analog Trigger (PFI0/TRIG1)
Impedance ................................................. 10 kΩ
Coupling ..................................................... DC
Protection
Digital trigger ........................................ -0.5 to (Vcc + 0.5) V
Analog trigger
On/Off/Disabled .............................. ±35 V
Calibration
Recommended warm-up time................... 15 minutes; 30 minutes for DAQCard
Calibration Interval ..................................... 1 year
Onboard calibration reference
DC Level
Temperature coefficient
Long-term stability
RTSI (PCI and ISA only)
Trigger lines................................................ 7
PXI Trigger Bus (PXI only)
Trigger lines................................................ 6
Star Trigger................................................. 1
Bus Interface
PCI, PXI...................................................... Master, slave
AT, DAQCard.............................................. Slave
Power Requirements
1
Physical
1
Dimensions (not including connectors)
1
PCI ........................................................ 17.5 by 10.6 cm (6.9 by 4.2 in.)
PXI ........................................................ 16.0 by 10.0 cm (6.3 by 3.9 in.)
ISA (long) .............................................. 33.8 by 9.9 cm (13.3 by 3.9 in.)
ISA (short)............................................. 17.5 by 9.9 cm (6.9 by 4.2 in.)
DAQCard .............................................. Type II PC Card
I/O connectors
Environment
Operating temperature .............................. 0 to 55 °C; DAQCards should not
exceed 55 °C while in PCMCIA slot
Storage temperature.................................. -20 to 70 °C
Relative humidity ....................................... 10 to 90%, noncondensing
Certifications and Compliances
CE Mark Compliance
1
See page 148 for RT Series devices power requirements and physical parameters.
16-Bit E Series NI 6052E, NI 603xE, and NI 601xE (continued)
6052E 5.000 V (±1.0 mV) Over full operating temperature,
6030E actual value stored in EEPROM
6031E
6032E
6033E
6012E
6034E 5.000 V (±3.5 mV)
6035E
6036E
6011E 5.000 V (±3.0 mV)
6052E ±0.6 ppm/°C max
6030E
6031E
6032E
6033E
6012E ±5.0 ppm/°C max
6034E
6035E
6036E
6011E ±2.0 ppm/°C max
6052E ±6.0 ppm/
6030E
6031E
6032E
6033E
6034E ±15.0 ppm/
6035E
6036E
601xE
6052E 68-pin male SCSI-II type
6030E
6032E
6034E
6035E
6036E
6011E
6031E 100-pin female 0.050 D-type
6033E
6012E 68-pin female PCMCIA
Device +5 VDC (±5%) Power Available at I/O Connector
6052E 1.3 A +4.65 to +5.25 VDC, 1 A
603xE (PCI, PXI); except 1.5 A +4.65 to +5.25 VDC, 1 A
6034E/6035E
6034E 0.9 A +4.65 to +5.25 VDC, 1 A
6035E
6036E
603xE (AT) 1.2 A +4.65 to +5.25 VDC, 1 A
PCI-MIO-16XE-50 1.1 A +4.65 to +5.25 VDC, 1 A
DAQCard-A1-16XE-50 230 mA +4.65 to +5.25 VDC, 250 mA
AT-MIO-16XE-50 750 mA +4.65 to +5.25 VDC, 1 A
√1000 h
√
1000 h
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels